¿Domotics? comes from the Domus Latin “House” that also is present in “the domestic”
word and of the suffix, - tic, that also is in Telematics,
office automation, robotics. The completion - tic means
automatic, and generally it induces the meaning of “Management
by computer science means”.
Another concept very related to the domotics is “Digital Home”, the “House Computerized” Set of systems that automate the different facilities
from a house.
Dimmer with input 0-5v or 10v (4-20mA.) with validation of
signal, for
home automation, PLC and other aplications, for Rail
Din
Four mode of work:
External wall switch
with neon pilot
Input opto-isolate
Push button in front panel
Input 0-5v or 0-10v.
For control without external system On-Off and dimming
For remote control for On-Off and dimming
Also for validation of signal 0-5v/0-10v.
For control without home automation system
On-Off and dimming
Signal 0-5v or 0-10v.
All the entrances vary the previous state of the Dimmer.
Also it can work of independent form in case of failure of
external system.
Output opto isolate for signal
state Dimmer (indicate if On or Off) 5...24v dc 10mA. max.
Work with
electronics transformer dimmable leading-edge dimming
You can buy and pay with Paypal
S2305V-S2310V
600w./400w.
S2335V-S2330V 1.500w./1.000w.
S2345V-S2340V
2.000w./1.600w.
Box for Rail Din 1 module (17mm)
Power: 600w
Resistive or 400w Inductive
Back connection Removable
with 6 contacts
Memory of Level and state by defect.
(On, Off and Level before the cut of the electrical
provision)
Box for
Rail Din 2 module (34mm)
Power: 1.500w Resistive or 1.000w
Inductive
Back connection with 6 contacts
Memory of Level and state by switch.
(On, Off and Level before the cut of the electrical
provision)
Box for
Rail Din 4 module (70mm)
Power: 2.000w Resistive or 1.600w
Inductive
Back connection with 6 contacts
Memory of Level and state by switch.
(On, Off and Level before the cut of the electrical
provision)
Input-0-5v/0-10v
Opto-isolate 0-5v or 10v.
In this
connection the Dimmer is commanded from a Automaton with
analogical exit by means of tension of 0 to 5v or 10v
(4-20mA), as much with fixed tensions of x value to generate
scenes or generating inclines of ascent or slope at the
speed that is desired from the external system.
This entrance has priority on the others, which is to say
when 0-5v or 10v receives a value with signal of validation,
the Dimmer will take this value.
Input validation
Opto isolate control and validation, On, Off, Dimming, 5…
24v dc./ac. (45 to 55ms, 100 to 200ms and + of 400ms.).
In this
connection worth the analogical signal of the entrance
Input-0-5v/0-10vwhen have one pulse
(45...55ms 5...24v.Dc). and also to command the Dimmer with
short pulses of 100 to 200ms for On or Off and long pulses (more
of 400ms) for the regulation of Dimmer.
Signal Validation
45...55ms. (5 to 24v.Dc.
On- Off
100...200ms. (5 to 24v.Dc.
Dimming
+ of 200ms. (5 to 24v.Dc.
Frontal push button andexternal wall switch:
With return to phase (It admits neon pilots in the wall
switch), to use the Dimmer of independent way in case of
failure of the automaton system or of independent way.
This exit will indicate to the
automaton if the Dimmer this on or off, is a connection that
will close an external circuit (Relay, LED, Max.load 10mA.)
Work with
electronics transformer and inductive load dimmable Leading-edge dimming
Power supply: 210...240v. 50Hz.
Without Neutral
Available versions 110v 60Hz.
Peripheral Dimmer with input 0-5v or 0-10v for home
automation, PLC and other aplications.
Four mode of work:
External wall switch
with neon pilot
Input opto-isolate
Push button in front
panel
Input 0-5v or 10v.
For control without external system
On-Off and dimming
For remote control for On-Off and dimming
For control without home automation system On-Off and dimming
Signal 0-5v or 10v.
All the entrances vary the previous state of the Dimmer.
Also it can work of independent form in case of failure of
external system.
Output opto isolate for signal
state Dimmer (On-Off) 5...24v dc 10mA. max.
Work with
electronics transformer and inductive load dimmable Leading-edge dimming
You can buy and pay with Paypal
S2305-S2310
600w./400w.
S2335-S2330 1.500w./1.000w.
S2345-S2340
2.000w./1.600w.
Box for Rail Din 1 module (17mm)
Power: 600w
Resistive or 400w Inductive
Back connection Removable
with 6 contacts
Memory of Level and state by defect.
(On, Off and Level before the cut of the electrical
provision)
Box for
Rail Din 2 module (34mm)
Power: 1.500w Resistive or 1.000w
Inductive
Back connection with 6 contacts
Memory of Level and state by switch.
(On, Off and Level before the cut of the electrical
provision)
Box for
Rail Din 4 module (70mm)
Power: 2.000w Resistive or 1.600w
Inductive
Back connection with 6 contacts
Memory of Level and state by switch.
(On, Off and Level before the cut of the electrical
provision)
Input Opto isolate 0-5v or 10v.
In this connection the Dimmer is commanded from a
Automaton with analogical exit by means of tension of 0 to
5v or
10v (4-20mA), as much with fixed tensions of x value to
generate scenes or generating inclines of ascent or slope at
the speed that is desired from the external system.
This entrance has priority on the others, and
when have 0-5v or 10v receives a value the Dimmer will take this value.
Input Opto isolate for remote
control For On, Off, Dimming, 5… 24v dc. /ac. (100
to 200ms and + of 400ms.).
In this connection can command
the Dimmer by short pulses (100 to 200ms.) for On or Off and long pulses
(more of 200ms.) for the
regulation of the Dimmer.
On- Off
100...200ms. (5 to 24v.Dc.
Dimming
+ of 200ms. (5 to 24v.Dc.
Frontal push button andexternal wall switch:
With return to phase (It admits neon pilots in the wall
switch), to use the Dimmer of independent way in case of
failure of the automaton system or of independent way.
Output opto isolate of supervision
5...24v dc./ac. 10mA.
This exit will indicate to the
automaton if the Dimmer this on or off, is a connection that
will close an external circuit (Relay, LED, fully factored
load 10mA.
Work with
electronics transformer dimmable Leading-edge dimming.
Peripheral Dimmer for
home automation, PLC and other aplications.
Three mode of work:
External wall switch
with neon pilot
Input opto-isolate
Push button in front
panel
For control without external system
On-Off and dimming
For remote control for On-Off and dimming
For control without home automation system, PLC On-Off and dimming
All the entrances vary the previous state of the Dimmer.
Also it can work of independent form in case of failure of
external system.
Output opto isolate for signal
state Dimmer (On-Off) 5...24v dc 10mA. max.
Work with
electronics transformer dimmable Leading-edge dimming
You can buy and pay with Paypal
S2311 600w./400w.
S2331 1.500w./1.000w.
S2341
2.000w./1.600w.
Box for Rail Din 1 module (17mm)
Power: 600w
Resistive or 400w Inductive
Back connection Removable
with 6 contacts
Memory of Level and state by defect.
(On, Off and Level before the cut of the electrical
provision)
Box for
Rail Din 2 module (34mm)
Power: 1.500w Resistive or 1.000w
Inductive
Back connection with 6 contacts
Memory of Level and state by switch.
(On, Off and Level before the cut of the electrical
provision)
Box for
Rail Din 4 module (70mm)
Power: 2.000w Resistive or 1.600w
Inductive
Back connection with 6 contacts
Memory of Level and state by switch.
(On, Off and Level before the cut of the electrical
provision)
Input Opto isolate for remote
control For On, Off, Dimming, 5… 24v dc. /ac. (100
to 200ms and + of 400ms.).
In this connection can command
the Dimmer by means of short pulses of 100 to 200ms for
ignite-dull and long pulses of more of 200ms for the
regulation of the Dimmer.
On- Off
100...200ms. (5 to 24v.Dc.
Dimming
+ of 200ms. (5 to 24v.Dc.
Frontal push button andexternal wall switch:
With return to phase (It admits neon pilots in the wall
switch), to use the Dimmer of independent way in case of
failure of the automaton system or of independent way.
Output opto isolate of supervision
5...24v dc./ac. 10mA.
This exit will indicate to the
automaton if the Dimmer this on or off, is a connection that
will close an external circuit (Relay, LED, fully factored
load 10mA.
Work with
electronics transformer dimmable Leading-edge dimming,
Input Opto isolate for Reset (Pulse
200...400ms 5...24v dc./ac.). Applying a pulse in this
connection it is possible to be extinguished to this and to
another Dimmer that is ignited of simultaneous form.
Power supply: 210...240v. 50Hz.
Without Neutral
Available versions 110v 60Hz.
New System Master-Slave
Master Dimmer for control simultaneous
for several Dimmer.
S2500
This command can be controlled up to 40 peripherals Dimmers in the series
0-5v or 0-10v.
Very useful to get the same brightness with several dimmers on the same circuit
lighting.
That it is
the Memory of level and state?: After a light cut, whatever duration of the cut, dimmer to
memorize the last state (if he were dull or ignition) and
the last used level. These options can be activated or not
in switch of the Dimmer.
We
recommend
to Dimmer works correctly, the transformers electronic
for halogen must be dimmable to triac, the use is not
recommended by some transformers of Asian origin if they are
not dimmables (Leading-edge dimming)
Not work with electronics
ballasts for fluorescent, only S9000 or dimmables
1-10v
